Five-minute(ish) Beanie is the Fastest We’ve Seen Yet
Yes, you read that right– not benchy, but beanie, as in the hat. A toque, for those of us under the Maple Leaf. It’s not 3D printed, either, except perhaps by the loosest definition of the word: it is knit, by [Kevr102]’smotorized turbo knitter.
The turbo-knitter started life as an Addi Express King knitting machine. These circular knitting machines are typically crank-operated, functioning with a cam that turns around to raise and lower special hooked needles that grab and knit the yarn. This particular example was not in good working order when [Kevr102] got a hold of it. Rather than a simple repair, they opted to improve on it.
A 12 volt motor with a printed gear and mount served for motorizing the machine. The original stitch counter proved a problem, so was replaced with an Arduino Nano and a hall effect sensor driving a 7-digit display. In theory, the Arduino could be interfaced with the motor controller and set to run the motor for a specific number of stitches, but in practice there’s no point as the machine needs babysat to maintain tension and avoid dropping stitches and the like. Especially, we imagine, when it runs fast enough to crank out a hat in under six minutes. Watch it go in the oddly cropped demo video embedded below.
Five minutes would still be a very respectable time for benchy, but it’s not going to get you on the SpeedBoatRace leaderboards against something like the minuteman we covered earlier.
If you prefer to take your time, this knitting machine clock might be more your fancy. We don’t see as many fiber arts hacks as perhaps we should here, so if you’re tangled up in anything interesting in that scene, please drop us a line.
youtube.com/embed/QWRVQVrnILk?…
Oscillator Negativity is a Good Thing
Many people who get analog electronics still struggle a bit to design oscillators. Even common simulators often need a trick to simulate some oscillating circuits. The Barkhausen criteria state that for stable oscillation, the loop gain must be one, and the phase shift around the feedback loop must be a multiple of 360 degrees. [All Electronics Channel] provides a thorough exploration of oscillators and, specifically, negative resistance, which is punctuated by practical measurements using a VNA. Check it out in the video below.
The video does have a little math and even mentions differential equations, but don’t worry. He points out that the universe solves the equation for you.
In an LC circuit, you can consider the losses in the circuit as a resistor. That makes sense. No component is perfect. But if you could provide a negative resistance, it would cancel out the parasitic resistance. With no loss, the inductor and capacitor will go back and forth, electrically, much like a pendulum.
So, how do you get a negative resistance? You’ll need an active device. He presents some example oscillator architectures and explains how they generate negative resistances.
Crystals are a great thing to look at with a VNA. That used to be a high-dollar piece of test gear, but not anymore.
youtube.com/embed/EG3BSn8MzHc?…
View a Beehive Up Close with this 3D Printed Hive
Bees are incredible insects that live and die for their hive, producing rich honey in complicated hive structures. The problem is as the average beekeeper, you wouldn’t see much of these intricate structures without disturbing the hive. So why not 3D print an observation hive? With [Teddy Hatcher]’s 3D printing creativity, that is exactly what he did.
Hexagonal sections allow for viewing of entire panels of hexagonal cells, growing new workers, and storing the rich syrup we all enjoy. Each module has two cell panels, giving depth to the hive for heat/humidity gradients. The rear of a module has a plywood backing and an acrylic front for ample viewing. [Teddy] uses three modules plus a Flow Hive for a single colony, enough room for more bees than we here at Hackaday would ever consider letting in the front door.
As with many 3D printed projects involving food or animals, the question remains about health down the line. Plastic can bio-accumulate in hives, which is a valid concern for anyone wanting to add the honey to their morning coffee. On the other hand, the printed plastic is not what honey is added to, nor what the actual cell panels are made from. When considering the collected honey, this is collected from the connected Flow Hive rather than anything directly in contact with 3D printed plastic.
Beehives might not always need a fancy 3D printed enclosure; the standard wooden crates seem to work just fine for most, but there’s a time and place for some bio-ingenuity. Conditions in a hive might vary creating problems for your honey production, so you better check out this monitoring system dedicated to just that!
youtube.com/embed/Qi3-rIL5Fbw?…
Thanks to [George Graves] for the tip!
Better Solid State Heat Pumps Through Science
If you need to cool something, the gold standard is using a gas compressor arrangement. Of course, there are definite downsides to that, like weight, power consumption, and vibrations. There are solid-state heat pumps — the kind you see in portable coolers, for example. But, they are not terribly efficient and have limited performance.
However, researchers at Johns Hopkins, working with Samsung, have developed a new thin-film thermoelectric heat pump, which they claim is easy to fabricate, scalable, and significantly more efficient. You can see a video about the new research below.
Manufacturing requires similar processes to solar cells, and the technology can make tiny heat pumps or — in theory — coolers that could provide air conditioning for large buildings. You can read the full paper in Nature.
CHESS stands for Controlled Hierarchically Engineered Superlattice Structures. These are nano-engineered thin-film superlattices (around 25 μm thick). The design optimizes their performance in this application.
The new devices claim to be 100% more efficient at room temperature than traditional devices. In practical devices, thermoelectric devices and the systems using them have improved by around 70% to 75%. The material can also harvest power from heat differences, such as body heat. The potential small size of devices made with this technology would make them practical for wearables.
We’ve looked at the traditional modules many times. They sometimes show up in cloud chambers.
youtube.com/embed/dOw_fzZh7MM?…
Spazio e industria, il direttore generale dell’Esa visita la nuova Space smart factory di Roma
@Notizie dall'Italia e dal mondo
Il direttore generale dell’Agenzia spaziale europea, Josef Aschbacher, ha visitato in anteprima la nuova Space smart factory di Thales Alenia Space a Roma. L’impianto, in via di completamento, sarà inaugurato dopo l’estate e
Notizie dall'Italia e dal mondo reshared this.
Budget Brilliance: DHO800 Function Generator
The Rigol oscilloscopes have a long history of modifications and hacks, and this latest from [Matthias] is an impressive addition; he’s been working on adding a function generator to the DHO800 line of scopes.
The DHO800 series offers many great features: it’s highly portable with a large 7-inch touchscreen, powered by USB-C, and includes plenty of other goodies. However, there’s room for enhancements. [Matthias] realized that while software mods exist to increase bandwidth or unlock logic analyzer functions, the hardware needed to implement the function generator—available in the more expensive DHO900 series—was missing.
To address this, he designed a daughterboard to serve as the function generator hardware, enabling features that software tweaks can unlock. His goal was to create an affordable, easy-to-produce, and easy-to-assemble interface board that fits in the space reserved for the official daughterboard in higher-end scopes.
Once the board is installed and the software is updated, the new functionality becomes available. [Matthias] clearly explains some limitations of his implementation. However, these shortcomings are outweighed by the tremendous value this mod provides. A 4-channel, 200 MHz oscilloscope with function generator capabilities for under $500 is a significant achievement. We love seeing these Rigol mods enhance tool functionality. Thanks, [Matthias], for sharing this project—great job bringing even more features to this popular scope.
Regalo riviste di moda vintage - Questo è un post automatico da FediMercatino.it
Prezzo: 0 Euro
Regalo riviste vintage.
Nel mio blog potete consultare la lista degli articoli in regalo.
Attenzione! Non effettuo consegne a mano.
Pagamento dei costi di spedizione tramite donazione con Paypal.
Leggi la descrizione ed i termini e condizioni del blog aggiornati secondo le direttive Europee.
Il BLOG NON ha finalità di lucro e non può averli in quanto frutto di un'iniziativa personale.
Il Mercatino del Fediverso 💵♻️ reshared this.
#Gaza, sterminio e resistenza
Gaza, sterminio e resistenza
La resistenza palestinese a Gaza continua a portare a termine operazioni complesse e altamente efficaci contro le forze sioniste di occupazione nonostante una situazione a dir poco catastrofica e l’avanzamento a passo spedito dei piani di pulizia etn…www.altrenotizie.org
Sesta generazione, ecco perché lo Scaf rischia di fare la fine dell’Eurofighter
@Notizie dall'Italia e dal mondo
Certi programmi non ingranano, fanno dei giri immensi e poi si arenano lo stesso. Questo appare il destino dello Scaf (Système de combat aérien du futur), il programma franco-tedesco-spagnolo per sviluppare un sistema di combattimento aereo di sesta generazione. Dassault Aviation (prime
Notizie dall'Italia e dal mondo reshared this.
IndoMed, così i laser cinesi disturbano la missione Aspides
@Notizie dall'Italia e dal mondo
Il ministero degli Esteri tedesco ha convocato l’ambasciatore cinese a Berlino, Ruiyu Li, per chiedere spiegazioni di quanto successo nel Mar Rosso, dove un laser di un’imbarcazione della Marina dell’Esercito popolare di liberazione avrebbe “inquadrato” un aereo con a bordo uomini della Deutsche
Notizie dall'Italia e dal mondo reshared this.
Questo pazzo pazzo Nobel
Candida anche tu il tuo premio Nobel per la Pace!
Tutto al costo di un francobollo da lettera per la Norvegia!
Puoi scegliere chi vuoi!
Lex Lutor, il Dottor Destino, Goblin, Ignazio La Russa... tutti sono candidabili!
Poliversity - Università ricerca e giornalismo reshared this.
EDIT: ho rifatto accesso e il problema n. 1 si è risolto (ma non il n. 2)
Sto (ri)provando a usare Raccoon e ho due problemi.
1) la timeline "Iscrizioni" mi appare vuota ("Qui non c'è nulla da visualizzare")
2) nella scheda Profilo vedo i miei post ma alcuni sono troncati (ho provato a cambiare la modà di visualizzazione su Completa", non funziona)
Uso l'ultima versione e sono su /e/OS.
N.B. sto usando Raccoon anche per il mio account mastodon.uno e con quello non ci sono problemi
Suggerimenti?
Grazie 🙏
@Signor Amministratore ⁂
Sì, è su "illimitato".
In particolare c'è un post che mi taglia molto presto.
Allego 2 screenshot: uno del post visualizzato nella scheda Profilo dal mio account Friendica (tema verde, post troncato) e uno dello stesso post aperto loggandomi dall'account Mastodon (tema blu, il post compare per intero).
🤔
L'opzione è su "illimitato"
I due screen si riferiscono allo stesso post, che viene troncato se lo apro nella scheda profilo loggandomi su poliverso.org ma viene visualizzato interamente se lo cerco dopo essermi loggato su mastodon.uno
@Tiziano sì, confermo che succede anche a me.
@𝔻𝕚𝕖𝕘𝕠 🦝🧑🏻💻🍕 riesci a capire perché Raccoon taglia post come questo?
⬇️
poliverso.org/display/0477a01e…
Tiziano :friendica: likes this.
@Signor Amministratore ⁂ @𝔻𝕚𝕖𝕘𝕠 🦝🧑🏻💻🍕 C'è un follow-up qui... e giuro che mi stanno simpatici i procioni 🙄
Il Pentagono sceglie Roboze per rafforzare la supply chain industriale. I dettagli
@Notizie dall'Italia e dal mondo
A Houston, in Texas, c’è un pezzo di Italia che sta guadagnando spazio nelle strette maglie dell’industria della difesa americana. Si tratta di Roboze, società deep tech con base a Bari e specializzata nella stampa 3D industriale di materiali compositi ad
Notizie dall'Italia e dal mondo reshared this.
freezonemagazine.com/articoli/…
Nelle notti infuocate e insonni di quest’ennesima estate — che sarà, di certo, meteorologicamente da dimenticare — il pensiero continua a rivolgersi agli accadimenti degli ultimi tre anni. Addormentarsi diventa ancora più difficile, perché il fardello che dobbiamo portare è sempre più pesante e la via d’uscita sembra non
Inseguito dai tedeschi riuscii a nascondermi rannichiandomi dietro una roccia grupposbarchi.wordpress.com/20…
Campi “umanitari” e città recintate: l’architettura della pulizia etnica a Gaza
@Notizie dall'Italia e dal mondo
Progetti Usa e israeliani alimentano ulteriormente il sospetto di un piano di espulsione della popolazione palestinese in via di elaborazione
L'articolo Campi “umanitari” e città recintate: l’architettura della pulizia etnica a Gaza proviene da
Notizie dall'Italia e dal mondo reshared this.
Turchia: nuova ondata di arresti di sindaci dell’opposizione
@Notizie dall'Italia e dal mondo
In Turchia la polizia ha arrestato altri sindaci dell'opposizione e il primo cittadino di Istanbul, principale sfidante di Erdogan alle presidenziali, rimane in prigione con accuse di corruzione
L'articolo Turchia: nuova pagineesteri.it/2025/07/08/med…
Notizie dall'Italia e dal mondo reshared this.
@devol
Come si fa a impostare l'istanza SearXNG di devol.it come motore di ricerca di default su Firefox?
Poliversity - Università ricerca e giornalismo reshared this.
È la prima cosa che ho provato ma a quanto ho capito non imposta l'istanza di devol.it ma quella di seek.fyi.
C'è differenza immagino, o no?
Non riesco a far funzionare i "!bang". Volevo cercare una parola usando il bang "!translate" e SearXNG di devol.it mi ha dato un errore, ho pensato fosse un caso particolare ma provandone altri mi sembra che ci sia effettivamente qualcosa che non va (o qualcosa che non capisco io nel funzionamento dei bang).
Metto un esempio nella screenshot qui sotto, in cui provo a fare una ricerca della parola "albero" su Wikipedia.
abbiamo provato altri e funzionano, qua c'è la guida: newsletter.devol.it/guida-comp…
evidentemente alcuni motori ci bloccano pensando che siamo dei bot.
Guida Completa a SearXNG: Privacy e Libertà nelle Tue Ricerche Online
SearXNG rappresenta una delle alternative più potenti e rispettose della privacy nel panorama dei motori di ricerca attuali. Questa guida vi illustrerà come configurare e utilizzare l'istanza italiana ospitata da Devol (searxng.devol.devol - fediverso (devol, la newsletter del fediverso e dei servizi liberi online)
freezonemagazine.com/rubriche/…
Nel maggio del 1973, Mark Knopfler lascia Leeds e l’Università dove si è laureato in Letteratura Inglese alla volta di Londra. Quando parte è un giovane professore precario di 24 anni e un giornalista praticante del quotidiano Yorkshire Evening Post. Gli piace la musica e impara a suonare la chitarra da solo aiutato in questo […]
L'articolo Il divano dei fratelli Knopfler proviene da FREE
Riviste vintage in regalo - Questo è un post automatico da FediMercatino.it
Prezzo: 0 Euro
Regalo riviste vintage.
Nel mio blog potete consultare la lista degli articoli in regalo.
Attenzione! Non effettuo consegne a mano.
Pagamento dei costi di spedizione tramite donazione con Paypal.
Leggi la descrizione ed i termini e condizioni del blog aggiornati secondo le direttive Europee.
Il BLOG NON ha fini di lucro e non può averli in quanto frutto di un'iniziativa personale.
Il Mercatino del Fediverso 💵♻️ reshared this.

𝓘𝓰𝓸𝓻 🏴☠️ 🏳️🌈 🇮🇹
in reply to 𝓘𝓰𝓸𝓻 🏴☠️ 🏳️🌈 🇮🇹 • •