When electronics release the Magic Smoke, more often than not it’s a fairly sedate event. Something overheats, the packaging gets hot enough to emit that characteristic and unmistakable odor, and wisps of smoke begin to waft up from the defunct component. Then again, sometimes the Magic Smoke is more like the Magic Plasma, as was the case in this absolutely smoked Omron programmable logic controller.

Normally, one tasked with repairing such a thing would just write the unit off and order a replacement. But [Defpom] needed to get the pump controlled by this PLC back online immediately, leading to the somewhat unorthodox repair in the video below. Whatever happened to this poor device happened rapidly and energetically, taking out two of the four relay-controlled outputs. [Defpom]’s initial inspection revealed that the screw terminals for one of the relays no longer existed, one relay enclosure was melted open, its neighbor was partially melted, and a large chunk of the PCB was missing. Cleaning up the damaged relays revealed what the “FR” in “FR4” stands for, as the fiberglass weave of the board was visible after the epoxy partly burned away before self-extinguishing.

With the damaged components removed and the dangerously conductive carbonized sections cut away, [Defpom] looked for ways to make a temporary repair. The PLC’s program was locked, making it impossible to reprogram it to use the unaffected outputs. Instead, he redirected the driver transistor for the missing relay two to the previously unused and still intact relay one, while adding an outboard DIN-mount relay to replace relay three. In theory, that should allow the system to work with its existing program and get the system back online.

Did it work? Sadly, we don’t know, as the video stops before we see the results. But we can’t see a reason for it not to work, at least temporarily while a new PLC is ordered. Of course, the other solution here could have been to replace the PLC with an Arduino, but this seems like the path of least resistance. Which, come to think of it, is probably what caused the damage in the first place.

youtube.com/embed/yZbEM-Sy79Q?…

hackaday.com/2024/11/21/quick-…

Visualization of magnetic skyrmions. (Credit: KRISS)
Magnetic skyrmions are an interesting example of solitons that occurs in ferromagnetic materials with conceivable solutions in electronics, assuming they can be created and moved at will. The creation and moving of such skyrmions has now been demonstrated by [Yubin Ji] et al. with a research article in Advanced Materials. This first ever achievement by these researchers of the Korea Research Institute of Standards and Science (KRISS) was more power efficient than previously demonstrated manipulation of magnetic skyrmions in thicker (3D) materials.

Magnetic skyrmions are sometimes described as ‘magnetic vortices’, forming statically stable solitons. In a broader sense skyrmions are a topologically stable field configuration in particle physics where they form a crucial part of the emerging field of spintronics. For magnetic skyrmions their stability comes from the topological stability, as changing the atomic spin of the atoms inside the skyrmion would require overcoming a significant energy barrier.

In the case of the KRISS researchers, electrical pulses together with a magnetic field were used to create magnetic skyrmions in the ferromagnetic (Fe₃GaTe₂, or FGaT) film, after which a brief (50 µs) electric current pulse was applied. This demonstrated that the magnetic skyrmions can be moved this way, with the solitons moving parallel to the electron flow injection, making them quite steerable.

While practical applications of magnetic skyrmions are likely to be many years off, it is this kind of fundamental research that will enable future magnetic storage and spintronics-related devices.

hackaday.com/2024/11/21/creati…

If you’re into CNC machining, mechanical tinkering, or just love a good engineering rabbit hole, you’re in for a treat. Substack’s [lcamtuf] has written a quick yet insightful 15-minute introduction to involute gears that’s as informative as it is accessible. You can find the full article here. Compared to Hackaday’s more in-depth exploration in their Mechanisms series over the years, this piece is a beginner-friendly gateway into the fascinating world of gear design.

Involute gears aren’t just pretty spirals. Their unique geometry minimizes friction and vibration, keeps rotational speeds steady, and ensures smooth torque transfer—no snags, no skips. As [lcamtuf] points out, the secret sauce lies in their design, which can’t be eyeballed. By simulating the meshing process between a gear and a rack (think infinite gear), you can create the smooth, rolling movement we take for granted in everything from cars to coffee grinders.

From pressure angles to undercutting woes, [lcamtuf] explores why small design tweaks matter. The pièce de résistance? Profile-shifted gears—a genius hack for stronger teeth in low-tooth-count designs.

Whether you’re into the theory behind gear ratios, or in need of a nifty tool to cut them at home, Hackaday has got you covered. Inspired? Read the full article by [lcamtuf] here.

hackaday.com/2024/11/21/gear-u…

A mouse is just two buttons, and a two-dimensional motion tracking system, right? Oh, and a scroll wheel. And a third button. And…now you’re realizing that mice can be pretty complicated. [DIY Yarik] proves that in spades with his impressive—and complex—mouse build. The only thing is, you might argue it isn’t really a mouse.

The inspiration for the mouse was simple. [Yarik] wanted something that was comfortable to use. He also wanted a mouse that wouldn’t break so often—apparently, he’s had a lot of reliability issues with mice in recent years. Thus, he went with a custom 3D-printed design with a wrist rest at the base. This allows his hand to naturally rest in a position where he can access multiple buttons and a central thumbstick for pointing. In fact, there’s a secondary scroll control and a rotary dial as well. It’s a pretty juicy control surface.

The use of a thumbstick is controversial—some might exclaim “this is not a mouse!” To them, I say, “Fine, call it a pointing device.” It’s still cool, and it look like a comfortable way to interface with a computer.

We’ve seen some other neat custom mice over the years, too, like this hilarious force-feedback mouse. Video after the break.

youtube.com/embed/GpYnQJRw7pw?…

hackaday.com/2024/11/21/custom…

A questo punto amici della Rogue Records vi attendiamo al varco.

Eh sì perché continuare a dare luce a prodotti di così alto lignaggio senza sbagliare un colpo sembra impresa davvero titanica. Certo, conosciamo la vostra competenza e la vostra passione, ma perdio fatelo uscire un 7" un po' inferiore alla media.
iyezine.com/the-woggles-anyway…
@Musica Agorà

The Woggles - Anyway the Wind / Slippin'out 7"

The Woggles - Anyway the Wind / Slippin'out 7" - The Woggles - Anyway the Wind / Slippin'out 7" se tale occasione ci sarà non si tratta comunque di questa perché la recente infornata di singoli offertaci dall'etichetta di Tolosa è nuovamente di una q…

^{Il Santo (In Your Eyes ezine)}

Buongiorno a tutti. 😊
Da quando, anni fa, ho abbandonato Facebook (e tutti gli altri social classici e tossici) e sono approdato nel Fediverso, tante cose sono cambiate nel mio modo di percepire il mondo social e il web in generale.
Per prima cosa ho aperto un account su Mastodon, poi ho conosciuto Friendica, Peertube e Pixelfed, ma ho sempre scritto quasi esclusivamente su Mastodon, a parte i video pubblicati su Peertube.
Stamattina ho pensato che sarebbe carino iniziare delle interazioni anche qui e cominciare a pubblicare pure su Pixelfed.
Questo messaggio è il primo passo del mio buon proposito.
Voi come siete giunti sul Fediverso? Quali sono state le motivazioni che vi hanno spinto a cambiare?

In lak'ech. 🙏
Marco